Skip to content

10 second timer

A 10 second timer for the classroom: it opens at 00:10, counts down to zero and rings a bell. Show it full screen or on the board. Each second removes exactly one tenth of the bar, so even a child who cannot read the digits sees the count, and it is free with a teacher sign-in.

Sign in free to run 10 secondsSee an example

Sign in to use the Timer

Free for teachers. One account opens every tool and keeps your work.

Sign in free

Timer

00:10

StartReset

This page's 10 second preset as the timer's engine draws it: 00:10 over a full bar, a single round, bell 1 at zero and no flash. It is what the class sees before you press Start.

Key facts

ready on the face when you sign in
00:10
of the bar per second, one step for each number
10%
the one second shown in the warning colour
00:01
when Repeat runs all 20 rounds
3:20

How it works

  1. Sign in. The timer waits at 00:10 in the bar display with bell 1 set.
  2. Ask the question or give the instruction first, so all ten seconds go to the answer.
  3. Press Start, or Enter while the timer has focus.
  4. On the bell, boards turn round or hands go up. Reset puts 00:10 back for the next question.

Examples

  • Show-me boards

    Dara reads out 7 times 8. The class writes on mini whiteboards while the bar runs, and every board goes up on the bell, so a late answer cannot be copied from a neighbour.

  • Counting down from ten

    In a reception class, Eli lets the children chant ten, nine, eight with the digits before carpet time. The bell is the signal to sit.

  • A lightning vote

    Farah shows two answers on the board and gives ten seconds to stand by the one you pick. When the bell rings, the vote is closed and she counts the sides.

Ways teachers use it

  • Quick answers that everyone gives

    A short fixed time stops the fastest hands taking every question. Ten seconds is enough to recall a fact or a spelling, and short enough that the lesson does not stall.

  • A count young children can see

    Each number on the face lines up with one tenth of the bar. A child who cannot yet read 00:07 can still see that most of the bar is gone.

  • Transitions with a clear end

    Ten seconds to get back to your seat, then ten seconds to close books. Set Repeat to 3 and one press gives three steps with a bell after each: 3 rounds take 0:30.

  • Quiz rounds without the mouse

    Set Repeat to 10 and read a question at every bell. The round of ten questions takes 1:40, and Round 4 of 10 under the bar tells you where you are.

Inputs, outputs and limits

What you put in
  • Custom time: 0 in min and 10 in s, already typed by this page
  • Quick buttons: 1, 5, 10 and 15 minutes; none of them is 10 seconds
  • Repeat: 1 to 20 rounds, a bell after each
  • Display Digits, Bar or Ring, and size Small, Medium or Large
  • Bell at zero, with 20 bells, no sound and a volume in steps of 10 percent
What you get
  • Digits from 00:10 to 00:00 with the bar under them
  • Bell 1 at zero and Time is up on the face
  • Round 2 of 3 and so on while Repeat runs more than one round
Limits
  • One round of 0:01 at the least and 999:59 at the most
  • Up to 20 rounds; 20 rounds of 10 seconds take 3:20
  • The warning colour comes at the last tenth, which here is the final second
What is kept
  • Nothing is saved on this page; the timer lives in the tab
  • Open on the board and it is saved with that screen in your account

Ten seconds, again and again

Repeat runs the same 10 second round as many as 20 times in a row. The bell rings at the end of each round and the next one starts at once, so there is no pause to plan around. The table gives the total for a few common counts.

Rounds of 10 seconds and how long they take
RepeatBellsTotal time
110:10
330:30
661:00
12122:00
20, the most203:20

On OpenEduCat Board the running timer also shows -1 min and +1 min. Take care with them on a time this short: -1 min ends a 10 second round at once, and +1 min after the bell adds a whole minute, six times this timer. For another ten seconds, press Reset and then Start.

Questions teachers ask

Do I need an account?

Yes. The timer needs a free teacher account. Sign in once on each device with Google, Microsoft or a code sent to your email, and you land on a timer that already reads 00:10.

Is this a 10 second countdown timer with sound?

Yes. Bell 1 rings at 00:00. Settings holds 19 more bells and a volume slider, or untick Bell at zero for a silent count.

Does a 10 second countdown stay right if the laptop sleeps?

Yes. Start fixes the end time against the clock, so the timer is right the moment the screen wakes.

Can I type 10 seconds myself?

Yes. Under Custom, type 0 in min and 10 in s. The quick buttons are 1, 5, 10 and 15 minutes, and the 0 key on a focused timer means 10 minutes, not 10 seconds.

Can the warning colour come earlier?

No. It always marks the last tenth of a round. On a 10 second timer that is the final second, when the face reads 00:01.

More ready-made versions

Each one opens the tool already set up after you sign in.

On OpenEduCat Board, this timer sits on the projector next to a name picker, groups and a sound meter.

Free account. Sign in once on each device. The board then works offline. Your timer here is on the board too.

Open the board

Ways teachers use it: Brain breaks, Active learning, Learning stations

Running a whole school? OpenEduCat for schools runs it in one system.

See OpenEduCat for schools
  • No student accounts.
  • No ads.
  • Data-processing agreement on request.
For schools

Was this useful?

Counted per page. Report a problem for bugs.